Before and After

Basement Laundry Room Mold Remediation

Basement Mold Removal After Mold Remediation

Mold Remediation around sump pump Sump Pump in Basement

These are before and after photos of a mold remediation job in a laundry of a basement. We started by setting up the negative air and containment according to NYS guidelines and covered all of the belongings. Then we cut the trench around the sump pump, so the weep holes would drain to the drain tile and we put on weep hole covers. We treated all of the areas in the containment area with Fosters First Defense Disinfectant and HEPA vacuumed and wiped down all of the surfaces. Finally, we applied two coats of Mold Proof Coating on all of the block walls. 

Basement Mold Remediation Job

Basement Wall with Mold After Basement Mold Remediation

Basement Mold Removal Finished Mold Removal

These are before and after photos of a mold remediation project Comprehensive Mold Management completed. We began by setting up the proper containment and negative air and covered all of the belongings, according to NYS guidelines. Then we removed all of the walls, insulation, ceilings, framing and items that the customer requested to be removed. We treated and cleaned the items that the customer wanted to save. We treated all areas inside the containment area with Fosters First Defense Disinfectant. CMM HEPA vacuumed and wiped down all of the surfaces and cleaned the debris out of the trench. We drilled drainage weep holes on all lower block walls to relieve water pressure in the block and installed plastic covers to divert the water into the trench. Finally, we applied two coats of our mold proof coating on all of the block walls. 

Basement Mold Remediation Job

Basement Mold Removal Finished Basement Mold Removal

For this project we completed work throughout various areas in the basement. We began by setting up negative air and the proper containment and covered all of the belongings. Then, we removed all of the carpet and padding. We removed four feet from the floor the drywall, insulation and trim on all outside walls. We treated all of the block walls throughout the basement with an EPA approved disinfectant. Then, we cleaned and HEPA vacuumed the block walls. We drilled 5/8 inch drainage weep holes on all lower block walls to relieve the water pressure in the block. We installed plastic covers over the weep holes to divert water into the trench. We cleaned the calcium and debris out of the trench. We installed new insulation and drywall on areas where it was removed. Next, we applied two coats of Mold Proof Coating on all of our block walls. We repainted all outside drywall walls. We replaced the sump pump and corrected the plumbing connections. 

Bedroom Mold Remediation

Bedroom Mold Remediation After Bedroom Mold Remediation

This is a mold remediation project that we completed in a bedroom.We set up the proper containment with negative air and covered all of the belongings. We removed the plaster, lath and insulation in the corner of the bedroom. Then, we treated all of the areas inside the containment area with Fosters First Disinfectant. Next, we applied three inches of high density closed cell spray foram on all wall cavities where the wall board was removed. Finally, we installed new wallboard and new base trim on all areas removed. We tape, mud, sand and made paint ready. 

Crawl Space and Basement Mold Remediation Job

Crawl Space Mold Crawl Space Mold Removed

Basement Mold Removal Basement Mold Remediation

This is a job where we did the mold remediation in the basement and crawl space. In the basement, we started off by setting up the proper containment and negative air and covered all of the belongings. We treated the block walls with an EPA approved disinfectant and cleaned and HEPA vacuumed the block walls. We drilled 5/8 inch drainage weep holes on all lower block walls to relieve pressure in the block and installed plastic covers over the weep holes to divert water into the trench. Finally, we applied two coats of our mold proof coating.

In the crawl space, we treated all areas inside the containment area with Fosters First Defense Disinfectant and HEPA vacuumed and wiped down all the surfaces. We removed the wood barrier caulked to hold in standing water and drilled relief holes down into the cores of the block at the threshold. Finally, we applied two coats of our mold proof coating on all of the block walls. 

Crawl Space Mold Remediation

Crawl Space Mold Before Crawl Space Mold After

We completed mold remediation in a crawl space beneath a house. We began by setting up the proper containment with negative air per the NYS Guidelines and covered all of the belongings. Then, removed all of the belongings, vapor barrier, and insulation from underside of home and bagged and removed all of the debris. Next, we sealed all the basement windows with foam board. We applied an EPA approved disinfectant and stain removed to underside of flooring. We applied our mold proof coating on all joists and flooring. Finally, we insulated the hatch with weatherstripping and installed a new moisture barrier on the ground. 

Basement Mold Remediation Job

Basement Mold Removal Basement Mold Proof Coating

Basement Mold Basement Mold Removal

This is a basement mold remediation job where we set up the proper containment and negative air and removed paneling/drywall around the perimeter of the basement and exterior walls. We treated all of the block walls with an EPA approved disinfectant, we cleaned and HEPA vacuumed the block walls. Then, we drilled drainage weep holes on all of the lower block to relieve water pressure. We installed plastic covers over the weep holes to divert water into the trench. Finally, we applied two coats of our mold proof coating. 

Attic Mold Removal and Insulation Job

Before Attic Mold After Attic Mold Removal

Before Attic Mold Removal After Attic Mold Removal

These are the before and after pictures of an attic mold remediation job. We set up negative air and the proper containment, we applied an EPA approved disinfectant and stain remover to all plywood and supports. We applied our mold proof coating to all plywood and supports. Finally, we baffled all rafters and did blown in insulation throughout the attic. 

Mold Remediation in Master Bathroom

Bathroom Before Mold Removal Bathroom After Mold Removal

Bathroom Mold Remediation Bathroom Mold Remediation

We started off by setting up containment with negative air and covered all of the belongings. We removed the entire ceiling down to the roof rafters and bagged and removed all of the debris. We treated all of the areas with a disinfectant and HEPA vacuumed and wiped down all surfaces. We installed new half inch moisture resistant greenboard drywall, we taped, mudded, sanded and made paint ready. Finally, we applied two coats of our Mold Proof Coating. 

Mold Remediation in Air Handler Room

Mold Removal Basement  Finished Mold Removal

These are the before and after photos in an air handler room. We set up containment with negative air and covered all of their belongings. We treated all of the areas inside the containment with Fosters First Defense Disinfectant. We applied two coats of our Mold Proof Coating on all block walls. 

Basement Mold Removal Job

Before Basement Mold Removal Syracuse After Basement Mold Removal Syracuse

Before Basement Mold Remediation Syracuse After Basement Mold Remediation Syracuse

These are before and after photos of a mold removal job in a basement. In this basement we assisted with removing all of the items and cleaning the belongings that were salvageable. We set up containment with negative air prior to beginning work. We treated all areas of the basement with an EPA approved disinfectant, cleaned and HEPA vacuumed all areas and wiped down all surfaces. We drilled drainage weep holes on all of the lower block walls to relieve water pressure, then installed plastic covers over the weep holes to divert water into the trench. Finally, we applied our mold proof coating on all block walls. 

Basement Crawl Space Mold Remediation Job

Crawl Space Mold Removal Syracuse Crawl Space Mold Remediation Syracuse

Crawl Space Mold Removal Syracuse Crawl Space Mold Remediation Syracuse

At this home we set up containment with negative air, then we removed a vapor barrier and mold contaminated debris. We treated the entire crawl space with an EPA approved mold killing primer on all areas of remaining staining. We also installed a Santa Fe Classic whole house large capacity dehumidifier. 



Attic Mold Remediation Job

 

 

This is an attic mold remediation job that Comprehensive Mold Management completed. We began by setting up containment and negative air, then applied an EPA approved disinfectant and stain remover to all of the plywood and supports. Next, we applied our Mold Proof Coating on all plywood and supports. In order to correct the moisture issue we installed a humistatic and thermostatic controlled power vent on the back side of the roof to increase air flow in the attic. In addition, we baffled all of the rafters and installed blown in insulation throughout the attic. 

Basement Mold Removal and Basement Waterproofing

 

 

Basement Mold Remediation

 

 

 

These are before and after pictures of a mold removal job of an entire basement. We set up containment with negative air and covered all their belongings. We removed the mold and applied a mold proof coating. In order to correct the moisture issue we drilled drainage weep holes on all of the lower block walls to relieve the water pressure in the block. We installed plastic covers over the weep holes to divert water into the trench.  


 

These are before and after pictures of a mold remediation job of a basement wall. We removed the mold and applied a mold proof coating. In order to correct the moisture issue we removed the existing sump pump crock and sump pump. Then we installed a new sump pump crock and new perforated drain tile around the perimeter of the basement.

Air Duct Cleaning - Cold Air Return

 

These are before and after pictures of an air duct cleaning job, in a cold air return. We used the negative air method, which compresses air into the duct system through a hose with a special nozzle, while the duct system is under negative air pressure. This nozzle is designed so that the compressed air propels it inside the duct while dislodging dirt and debris. The dislodged dirt and debris become airborne and are drawn down through the duct and out of the system by the high power vacuum equipment. Regardless of how effiecient the cleaning process is, some small particles will remain in the cracks. We can apply a product called soot set that will lock down any remaining particles to ensure that no leftover debris spreads throughout the home.

Home Mold Removal and Tear-Out Job

 

These are before and after pictures of a home where we had to remove the mold and do a full tear-out. The home had a pipe burst and water was leaking in for several months, while the homeowner was out of town. Comprehensive Mold Management removed and cleaned up all areas of the home covered in mold.